Bacharach PCA2 Specifikace Strana 81
- Strana / 116
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Instruction 24-9448 5-5
Calibration
known temperature that will be applied for
calibration purposes.
4. Set thermocouple simulator to 32 °F (0 °C),
and then use the and buttons to enter
an Applied value that exactly equals the set-
ting of the simulator.
Alternatively: Submerge probe tip into an ice-
water bath with a thermometer, wait several
minutes, and then use the and buttons
to enter an Applied value that exactly equals
the thermometer reading.
The calibration range is from 32 to 41 °F (0
to 5 °C). An attempt to calibrate outside this
range will cause the message “Applied Value
High" (or Low) to appear at the bottom of the
screen.
5. Wait until the Measured reading stabilizes,
and then press ENT to calibrate the TS-Zero
Measured value to that of the Applied value;
after which the message “Good Calibration” should briefly appear fol-
lowed by the CALIBRATE TS-SPAN screen.
TS-Span Procedure:
6. Set thermocouple simulator to 572 °F (300 °C), and then use the
and buttons to enter an Applied value that exactly equals the
setting of the simulator.
Alternatively: Submerge probe tip into a container of boiling water with
a thermometer, wait several minutes, and then use the and
buttons to enter an Applied value that exactly equals the thermometer
reading.
The calibration range is from 175 to 625 °F (80 to 330 °C). An attempt
to calibrate outside this range will cause the message “Applied Value
High” (or Low) to appear at the bottom of the screen.
7. Wait until the Measured reading stabilizes, and then press ENT to cali-
brate the TS-Span Measured value to that of the Applied value; after
which the message “Good Calibration” should briefly appear followed by
the CALIBRATION LIST screen being re-displayed.
CALIBRATE TS-ZERO
Measured 34 °F
Applied 032 °F
Press ENT
to calibrate
06/27/06 11:55:30 PM
PRINT
F1 F2 F3
CALIBRATE TS-SPAN
Measured 574 °F
Applied 572 °F
Press ENT
to calibrate
06/27/06 11:55:30 PM
PRINT
F1 F2 F3
- Portable Combustion Analyzer 1
- WARRANTY 2
- Contents 3
- Instruction 24-9448 4
- 1 Introduction 7
- Instruction 24-94481-2 8
- Instruction 24-9448 1-3 9
- 1.3 Features & Benefits 10
- 1.4 Operational Overview 11
- 1.5 Connector Descriptions 12
- Figure 1-1. PCA 2 Components 13
- 1.5.3 POWER (AC Adapter) 14
- 1.6 Front Panel Buttons 15
- Instruction 24-94481-10 16
- Introduction 16
- 2 Specifications 17
- Normal Operating Conditions: 18
- Performance: 18
- Instruction 24-9448 2-3 19
- Specications 19
- Instruction 24-94482-4 20
- 3 Initial Setup 21
- 3.1 Scope 21
- 3.2 Power 21
- Instruction 24-94483-2 22
- Initial Setup 22
- T-STACK T-AIR 23
- 3.4 Operating Parameters 24
- 3.5 Fuel Selection 24
- Instruction 24-9448 5 25
- 3.7 Pressure Units Selection 26
- Instruction 24-9448 7 27
- 3.9 Date Setup 28
- 3.10 Time Setup 29
- Reference Setup 30
- Instruction 24-9448 11 31
- O2 4.0 % 32
- CO 12 ppm 32
- EFF 82.6% 32
- Instruction 24-9448 13 33
- 3.15 Logging Selection 34
- 3.16 Button Sound 34
- 3.17 Test ID Information 35
- Instruction 24-944816 36
- 3.18 Username 37
- Instruction 24-944818 38
- 3.19 Language 39
- 3.20 Cal Reminder Period 40
- 3.21 Run/Hold Screen Format 41
- Instruction 24-944822 42
- Instruction 24-9448 23 43
- 4 Operation 44
- 4.1 Operating Tips 44
- --- % 45
- T-STK 71.5 °F 45
- T-AIR 71.5 °F 45
- EA --- % 45
- CO(0) --- ppm 45
- 4.3 Selecting a Fuel 46
- 4.4 Sampling Point 47
- Instruction 24-9448 4-5 48
- Operation 48
- 4.6 Pressure Label Selection 50
- Instruction 24-94484-8 51
- 4.9 Saving Test Data 53
- 4.10 Ending a Combustion Test 54
- 4.11 Emptying the Water Trap 54
- 4.13 Low Battery Alarm 55
- 4.14 Data Logging 56
- Instruction 24-94484-14 57
- Instruction 24-9448 4-15 58
- Instruction 24-94484-16 59
- Where: “xx” is the memory 59
- 4.15 Memory 60
- Instruction 24-94484-18 61
- Instruction 24-9448 4-19 62
- 4.15.3 Clearing Memory 63
- Instruction 24-9448 4-21 64
- Instruction 24-9448 4-23 66
- Instruction 24-94484-24 67
- Select (Advanced) 68
- Name of new USB 68
- Instruction 24-9448 4-25 68
- 4.16.3 Recovering Data 69
- Instruction 24-9448 4-29 72
- Instruction 24-94484-30 73
- 4.18 Printing Test Data 74
- ∗∗∗) appear in the data 75
- Instruction 24-9448 4-33 76
- 5 Calibration 77
- 5.1 Smart Sensors 77
- 5.2 Starting a Calibration 77
- 5.3 Pressure Sensor 78
- Calibration 78
- 5.4 T-Stack Calibration 80
- ENT to calibrate the TS-Zero 81
- ENT to cali 81
- 5.5 T-Air Calibration 82
- Instruction 24-9448 5-7 83
- 5.6 CO-LO Sensor Calibration 84
- ENT to calibrate the H 85
- Sensor Calibration 86
- 5.8 NO Sensor Calibration 87
- ENT to calibrate the NO 89
- ENT to display 89
- 6 Maintenance 91
- 6.1 PCA 2 Disassembly 92
- Type and position 93
- +∆P (Top) 93
- –∆P (Bottom) 93
- PRESSURE 94
- PURGE AIR 94
- Figure 6-4. Wiring 95
- Instruction 24-94486-6 96
- 6.3 Smart Sensor Replacement 97
- 6.4 Sensor Only Replacement 98
- Instruction 24-9448 6-9 99
- Instruction 24-94486-10 100
- Maintenance 100
- 6.6 Thermocouple Replacement 101
- Instruction 24-94486-12 102
- 6.7 Pump Replacement 103
- 6.8 Cleaning the Probe 104
- 7.1 Analyzer Repair 105
- 7.2 Error Symbols 105
- 7 Troubleshooting 105
- Instruction 24-94487-2 106
- Troubleshooting 106
- ENT to display the 107
- ENT to display the DEVICE 108
- 8 Parts & Service 109
- 8.1 Replacement Parts 109
- Figure 8-1. Parts (2 of 2) 111
- 8.2 Accessories 112
- Instruction 24-9448 8-5 113
- Parts & Service 113
- 8.3 Service Centers 114
- Printed in U.S.A 116
Související produkty a manuály pro Měření, testování a kontrola Bacharach PCA2
(20 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.086 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce